Air speed for drying
Air speed for drying
In Marianski and Marianski they talk about air speed for drying. They suggest a speed of .1 to .5 meters per second.
when I search the web for slow speed fans, the technical detail is stated in cubic feet or meter per unit of time.
Any suggestion on a good slow volume of air for fan?
when I search the web for slow speed fans, the technical detail is stated in cubic feet or meter per unit of time.
Any suggestion on a good slow volume of air for fan?
Trying to achieve the exact velocity of air in the chamber is impossible without appropriate measuring devices. You can calculate the velocity based on the speed if you were forcing the air through a duct, so probably there is a formula where you factor in the size of the chamber and the amount of resistance. Having said that, .1 to .5 meters per second is very mild air movement. Keep in mind that the reason that we want a small amount of air movement in the chamber is not that we want to dry the sausages with the air speed, but rather to homogenize the humidity inside the chamber. Excessive air velocity will result in case hardening. Often it is not necessary to install a fan inside the chamber for the purpose of air circulation if you are using a frost free fridge that turns on on a regular basis, since that task is performed by the fan inside the fridge.
Thanks for the replies.
I understand the need for air movement. My concern or interest centered on how little or low 0.1 m/s actually was and whether such fans truly exist.
I live in Northern California on the coast around 80 miles south of the Oregon border. At this time of year I am not concerned with temperature since ambient temperature is around 50' F. Humidity bounces around but 80% is about the going value.
I am using an old refer for a chamber and temp and humidity are steady without using any equipment. So I was more concerned about days of no air movement. Perhaps I should just open the refer doors once a day and call it good enough.
I understand the need for air movement. My concern or interest centered on how little or low 0.1 m/s actually was and whether such fans truly exist.
I live in Northern California on the coast around 80 miles south of the Oregon border. At this time of year I am not concerned with temperature since ambient temperature is around 50' F. Humidity bounces around but 80% is about the going value.
I am using an old refer for a chamber and temp and humidity are steady without using any equipment. So I was more concerned about days of no air movement. Perhaps I should just open the refer doors once a day and call it good enough.
Fishhead, an ideally constructed curing chamber has has very slow, and if not continual, regular air movement as well as regular ventilation/air exchange. But many hobbyists have had success in simply doing what you are proposing, that is to open and close the door of the chamber a few times a day. This approach, however, becomes problematic once you load it to the full with fresh product which will raise the humidity dramatically. With ambient temp of 50F, your fridge does not cut in too often so you might not have enough air movement generated by the fan when the compressor kicks in (assuming your fridge is "frost-free"). An inexpensive opton woud be to install a vent to purge the inside air using an inexpensive computer fan with a timer. Computer fans run on 12v, but you can slow it down by using a lower voltage adapter or running it through a dimmer switch.
So all I can say is, experiment, adjust and see what kind of results you get. And don't hesitate to post further questions.
So all I can say is, experiment, adjust and see what kind of results you get. And don't hesitate to post further questions.
-
- Forum Enthusiast
- Posts: 573
- Joined: Fri Dec 18, 2015 23:35
- Location: Chicago
-
- Forum Enthusiast
- Posts: 573
- Joined: Fri Dec 18, 2015 23:35
- Location: Chicago
I boughts the tracks at a hardware store. As far as the plates, I have a laser cutter, so I cut them on thr laser cutter using 1/8' styrene. I also vut spares with no hole if I ever want to remove the fans and close them up. There's a little slack in the track, but nothing a little screen hasket didnt take care of
-
- Forum Enthusiast
- Posts: 573
- Joined: Fri Dec 18, 2015 23:35
- Location: Chicago
When you said "wired into a small 30.00 computer fan speed controller that allows you to alter the speed" I expected some units behind the 30.00. I am assuming that this is some type of a rheostat. I am not especially electronically gifted, but I can usually get things wired.
As for timers, I am familiar with timers that my wife plugs in when we go out of town, but not ones that would trigger an on/off event for a few minutes every hour. Can you point me in the right direction to where I could find one of these?
As for timers, I am familiar with timers that my wife plugs in when we go out of town, but not ones that would trigger an on/off event for a few minutes every hour. Can you point me in the right direction to where I could find one of these?
-
- Forum Enthusiast
- Posts: 573
- Joined: Fri Dec 18, 2015 23:35
- Location: Chicago
Here's the controller. You will need a small plug in power supply also. I will get you the voltage later. https://www.google.com/search?q=compute ... psQgTYI8AQ
-
- Forum Enthusiast
- Posts: 573
- Joined: Fri Dec 18, 2015 23:35
- Location: Chicago
Just got my small chamber going and loaded full of fresh product. The RH is at 90% on its own. If I run my fan I can get the RH down as the inflow air is around 30%. My shed temp. is 13C so the chamber isn't actually kicking in to cool, and my milk fridge isn't frost free. Should I leave the RH at 90 and just run the fan a few times a day to get fresh air in, or run it lots to keep RH down?
Thoughts?
Thoughts?